NGB / DRILLING EQUIPMENT
Equipment readiness sets the pace of well construction. Our own fleet, disciplined maintenance and accountability for every component support safe operations and fewer unplanned shutdowns.
Working ahead of failure through preventive maintenance, condition checks and timely service. NPT means non-productive time.
At NGB, owning equipment means taking responsibility for its technical condition. Our priorities are people’s safety, equipment readiness for operating loads and reducing the risk of unplanned shutdowns.
We combine preventive maintenance with manufacturer recommendations and checks of actual component condition. High technical standards depend on daily discipline, traceable work and sound decisions by our mechanical team.
Maintenance records capture inspections, operating hours, completed work, component replacements and upcoming service intervals. A consistent history for each asset supports service-life management and timely technical decisions.
Qualified personnel carry out daily condition checks, plan maintenance and verify readiness for operation. Repair quality, correct installation and post-service checks form one continuous process.
Specialist maintenance and repairs are entrusted exclusively to official dealers and manufacturer-authorised service partners with verified competence and the required certification.
We use genuine spare parts and manufacturer-recommended consumables with verified provenance. Counterfeit components and parts of unknown origin are unacceptable.
We develop our specialists’ competence, refine technical procedures and apply lessons from equipment operation. Accountability extends to every asset we bring to a project.
TECHNICAL SPECIFICATIONS
Equipment configuration, models and parameters — from hoisting systems and the top drive to mud pumps and the circulating system.
KEY EQUIPMENT
Top drive system with an electric AC drive.
PLC with touchscreen. Full telemetry: torque, speed and load.
A short list of the principal units. Each item links to its section in the complete specification table.
| Equipment | Model / type | Key specifications |
|---|---|---|
| 01TOP DRIVEDetailed specification |
TDS-500 |
Nominal load capacity: 225 t. Electric AC drive; 500 kW motor. Torque: 50 kN·m nominal / 65 kN·m maximum. Maximum speed: 250 rpm. PLC with touchscreen; torque, speed and load telemetry. |
| 02Drilling rigDetailed specification |
ZJ40 Manufacturer: DFXK NAFTOMASH LLC. |
Mobile rig. Permissible hook load: not less than 225 t. Nominal drilling depth: not less than 4,000 m. Power: 1,000 hp; circulation system volume: 280 m³. |
| 03DrawworksDetailed specification |
JC40DBL-1000-225 |
Drive power: 1,000 hp; hook load: 225 t. 5 speeds; drilling line diameter: 32 mm. |
| 04Mud pumpDetailed specification |
F-1300 |
Rated power in the specification: 1,000 hp; 3 cylinders. Maximum working pressure: 34.5 MPa. Maximum flow: 1,250 L/min at Ø180 mm / 1,450 L/min at Ø200 mm. |
| 05Rotary tableDetailed specification |
RTSL-500 |
Maximum torque: 48 kN·m; maximum speed: 300 rpm. Table internal diameter: 500 mm; mechanical drive. |
| 06Hoisting systemDetailed specification |
DG225-6×6 Crown block TG225-6×6 Travelling block Y225 Hook |
Nominal load of each unit: 225 t. Crown and travelling blocks: 6 sheaves each, Ø762 mm; Ø32 mm line. Hook: automatic locking device with spring latch. |
| 07MastDetailed specification |
Model not specified in the source. |
Mast height: 36 m; useful height: 32 m. Maximum static hook load: not less than 225 t. Permissible wind speed: 38.6 m/s. |
| 08SubstructureDetailed specification |
DZ225CX11 |
Maximum load: 225 t; height: 9 m. Hydraulic lifting system; 4 hydraulic jacks. |
| 09Drilling lineDetailed specification |
6×36WS-IWRC-1770 |
Diameter: 32 mm; working length: 4,000 m. Breaking load: not less than 565 kN; minimum safety factor: 5:1. |
| 10Mud systemDetailed specification |
Mud Circulating System System type stated in the source. |
Total volume: 280 m³; 4 sections; 8 agitators, 7.5 kW each. 2 shakers; shaker throughput: 160 m³/h. Vacuum degasser: 240 m³/h; centrifuge: 40 m³/h. |
| 11Standpipe manifoldDetailed specification |
Stand Pipe Manifold Equipment type stated in the source. |
Working pressure: 35 MPa nominal / 40 MPa maximum. Bore: 76 mm (3″); outlets: 2–3. |
| 12Power supplyDetailed specification |
Perkins / Cummins Makes stated in the source; exact models are not specified. |
Main generator: 600 kW; backup: 300 kW. 1 generator of each type; 400/230 V, 50 Hz. |
| 13Pneumatic systemDetailed specification |
Electric screw compressor; model not specified. |
Capacity: 6 m³/min; working pressure: 0.8 MPa. Receiver capacity: 1,000 L. |
Models and ratings are taken from the source specification. Where an exact model is absent, this is stated; a type or make has not been replaced with an invented model.
The complete inventory, individual system parameters and auxiliary equipment are available in the second tab.
Open the full tableScroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1 | Type | – | ZJ40 mobile drilling rig |
| 2 | Year of manufacture, not earlier than | Year | 2016 |
| 3 | Manufacturer | – | DFXK NAFTOMASH LLC |
| 4 | Permissible hook load, minimum | Metric tonne | 225 t |
| 5 | Rig power | hp | 1000 |
| 6 | Nominal drilling depth, minimum | m | 4000 |
| 7 | Circulating system volume | m³ | 280 |
| 8 | Rig electrical equipment (applicable standard) | – | API Spec 7K |
| 9 | Rig earthing system (applicable standard and technical specifications) | – | API Spec 7K, DSTU EN 16228-1:2016 (EN 16228-1:2014, idt) |
| 10 | Rig lighting | °C | From –20 to +55 |
| 11 | Operating temperature range | °C | From –20 to +55 |
| 12 | Weight of the heaviest assembly | Metric tonne | 48 t |
| 13 | Number of truckloads | pcs | 8 truckloads (according to the equipment data sheet) |
| 14 | Current location (nearest settlement, country) | – | Ukraine |
| 15 | Foundation type for mast and drilling equipment | – | Reinforced concrete slabs |
| 16 | Site dimensions for rig and crew camp | m | 120 × 144 |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Applicable standard and technical specifications | – | API Spec 4F |
| 1.2 | Maximum static hook load, minimum | Metric tonne | 225 |
| 1.3 | Overall height, including substructure | m | 39 |
| 1.4 | Mast height | m | 36 |
| 1.5 | Usable mast height | m | 32 |
| 1.6 | Permissible wind speed | m/s | 38,6 |
| 1.7 | Operating temperature range | °C | From –19 to +50 |
| 2Mast equipment | |||
| 2.1 | Derrickman’s platform | set | Included |
| 2.2 | Height adjustment above the rig floor (intervals) | m | 20,8; 23,8; 28,8 |
| 2.3 | Drill-collar handling mechanism at the derrickman’s platform (jacking winch) | t | 1 |
| 2.4 | Derrickman’s platform pipe-racking capacity | stands | 4000 m – Ø4½″; 3500 m – Ø5½″ |
| 2.5 | Windproof wall panels | set | Included |
| 2.6 | Attachment for the derrickman’s emergency escape system | – | Height 2.6 m |
| 2.7 | Equipment maintenance platforms | set | Included |
| 2.8 | Stairs and caged ladders | set | Included |
| 2.9 | Equipment set for raising the mast, substructure and drawworks | – | Not used |
| 2.10 | Deadline stabiliser | set | Included |
| 2.11 | Fast-line guard (stabiliser) | set | Included |
| 2.12 | Mast standpipe | set | 4″ |
| 2.13 | Gate valves | – | Z23Y100–35 MPa |
| 2.14 | Safety components | set | Included |
| 2.15 | Wind dampers | set | Included |
| 2.16 | Crown-block warning lights | – | Included |
| 2.17 | Counterweight system | set | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | DZ225CX11 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 4F |
| 1.3 | Maximum load | t | 225 |
| 1.4 | Substructure height | m | 9 |
| 1.5 | Structural weight | t | 50 |
| 1.6 | Construction material | – | Q345B steel |
| 1.7 | Number of sections | pcs | 2 |
| 1.8 | Section length | m | 9 / 4,5 |
| 1.9 | Operating temperature range | °C | From –19 to +50 |
| 1.10 | Hydraulic substructure lifting system availability | – | Included |
| 1.11 | Drive type for the hydraulic substructure lifting system | – | Hydraulic |
| 1.12 | Substructure locking system during lifting | – | Mechanical |
| 1.13 | Transition platform design between substructure and rig | – | All-metal |
| 2Additional substructure equipment | |||
| 2.1 | Substructure lifting system | set | Included |
| 2.2 | Hydraulic jacks | pcs | 4 |
| 2.3 | Hydraulic power unit for jack control | set | Included |
| 2.4 | Wellhead maintenance platforms | – | Included |
| 2.5 | Hatch or stairs for wellhead access | – | Included |
| 2.6 | Height-adjustable substructure supports | – | Included |
| 2.7 | Floor decking | – | Removable metal decking |
| 2.8 | Fastener set | – | Complete |
| 2.9 | Earthing system | – | Included |
| 2.10 | Work-area lighting | – | Included |
| 2.11 | Personnel evacuation system | – | Included |
| 2.12 | Safety barriers | – | Included |
| 2.13 | Anti-corrosion coating components | – | Included |
| 2.14 | Drill-string weight sensor | – | Model ZJ-225-W |
| 2.15 | Load indication system | – | Included (analogue and digital) |
| 2.16 | Power and signal cables | – | Included in the set |
| 2.17 | Hydraulic power unit heating system | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | DG225-6×6 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 8A / 8C |
| 1.3 | Rated load | t | 225 |
| 1.4 | Number of line parts | pcs | 6 |
| 1.5 | Line diameter | mm | 32 |
| 1.6 | Number of sheaves | pcs | 6 |
| 1.7 | Sheave diameter | mm | 762 |
| 1.8 | Bearing type | – | Tapered roller bearings |
| 1.9 | Housing material | – | 42CrMo steel |
| 1.10 | Crown-block weight | t | 6,3 |
| 1.11 | Operating temperature range | °C | From –19 to +50 |
| 1.12 | Lubrication system | – | Centralised, automatic |
| 1.13 | Reeving arrangement | – | 6×6 |
| 1.14 | Load on the rotation axis | kN | 2205 |
| 1.15 | Condition-monitoring components | – | Visual inspection windows |
| 1.16 | Travelling-block travel limiter | – | Included (mechanical stop) |
| 2Crown-block equipment | |||
| 2.1 | Sheave assembly | set | Included |
| 2.2 | Housing with guides | set | Included |
| 2.3 | Mounting shaft | set | Included |
| 2.4 | Suspension bracket | set | Included |
| 2.5 | Sheaves with bearings | set | 6 |
| 2.6 | Protective covers | set | Included |
| 2.7 | Centralised lubrication system | set | Included |
| 2.8 | High-strength bolted connections | set | Included |
| 2.9 | Equipment data sheet and certificate of conformity | – | Included |
| 2.10 | Crown-block lifting hook | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | TG225-6×6 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 8A / 8C |
| 1.3 | Rated load | t | 225 |
| 1.4 | Number of sheaves | pcs | 6 |
| 1.5 | Sheave diameter | mm | 762 |
| 1.6 | Line diameter | mm | 32 |
| 1.7 | Reeving arrangement | – | 6×6 |
| 1.8 | Bearing type | – | Tapered roller bearings |
| 1.9 | Hook suspension type | – | Slings with eyes |
| 1.10 | Shaft type | – | Removable |
| 1.11 | Housing material | – | 42CrMo steel |
| 1.12 | Travelling-block weight | t | 7,8 |
| 1.13 | Operating temperature range | °C | From –19 to +50 |
| 1.14 | Lubrication system | – | Centralised, automatic |
| 1.15 | Travel limiting system | – | Included (mechanical) |
| 1.16 | Line-retaining device during spooling | – | Included |
| 1.17 | Load on the rotation axis | kN | 2205 |
| 1.18 | Efficiency factor | % | 98 |
| 2Travelling-block equipment | |||
| 2.1 | Travelling-block housing | set | Included |
| 2.2 | Sheaves with bearing assemblies | set | 6 |
| 2.3 | Shafts with retainers | set | Included |
| 2.4 | Suspension hooks | set | Included |
| 2.5 | API-certified slings | set | Included |
| 2.6 | Centralised lubrication system | set | Included |
| 2.7 | High-strength bolted connections | set | Included |
| 2.8 | Equipment data sheet and certificate of conformity | – | Included |
| 2.9 | Condition-monitoring system | – | Visual inspection windows |
| 2.10 | Transport fittings (removable lifting eyes) | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | Y225 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 8A / 8C |
| 1.3 | Rated load | t | 225 |
| 1.4 | Design | – | One-piece housing with sling suspension |
| 1.5 | Connection type | – | API-threaded or travelling-block connection |
| 1.6 | Own weight | t | 2,5 |
| 1.7 | Assembled hook height | mm | 2360 |
| 1.8 | Hook rotation angle about its axis | degrees | 360 |
| 1.9 | Bearing assembly type | – | Combined (radial-thrust) |
| 1.10 | Load on the bearing assembly | kN | 2205 |
| 1.11 | Hook locking device type | – | Automatic (spring lock) |
| 1.12 | Housing design | – | Forged steel, heat-treated |
| 1.13 | Material | – | 42CrMo steel |
| 1.14 | Coating | – | Anti-corrosion polyurethane paint |
| 1.15 | Operating temperature range | °C | From –19 to +50 |
| 1.16 | Lubrication | – | Through grease nipples |
| 1.17 | Self-opening prevention mechanism | – | Included |
| 1.18 | Anti-sway mechanism | – | Included |
| 1.19 | Raised-position locking device | – | Included |
| 1.20 | Equipment data sheet and API certificate | – | Included |
| 2Hook equipment | |||
| 2.1 | Hook body with swivel head | set | Included |
| 2.2 | Complete bearing assembly | set | Included |
| 2.3 | Locking mechanism with retainer | set | Included |
| 2.4 | Self-opening prevention device | set | Included |
| 2.5 | Grease nipples | pcs | 2 |
| 2.6 | Gasket and seal set | set | Included |
| 2.7 | High-strength bolts and split pins | set | Included |
| 2.8 | Equipment data sheet and certificate of conformity | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | JC40DBL-1000-225 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 7K |
| 1.3 | Rated hook load | t | 225 |
| 1.4 | Drive power | hp | 1000 |
| 1.5 | Number of speeds | pcs | 5 |
| 1.6 | Drum diameter | mm | 610 |
| 1.7 | Drum width | mm | 410 |
| 1.8 | Line diameter | mm | 32 |
| 1.9 | Drum capacity | m | 800 |
| 1.10 | Maximum lowering speed under load | m/s | 1,2 |
| 1.11 | Maximum unloaded hoisting speed | m/s | 1,8 |
| 1.12 | Gearbox transmission ratio | – | 17,3:1 |
| 1.13 | Main brake type | – | Band, double-band |
| 1.14 | Main brake torque | kN·m | 30 |
| 1.15 | Auxiliary brake type | – | Electromagnetic or water brake |
| 1.16 | Auxiliary brake torque | kN·m | 25 |
| 1.17 | Brake control | – | Pneumohydraulic |
| 1.18 | Clutch type | – | Pneumatic, friction |
| 1.19 | Number of clutches | pcs | 4 |
| 1.20 | Gearbox type | – | Planetary, three-stage |
| 1.21 | Lubrication system | – | Centralised, forced |
| 1.22 | Gearbox cooling | – | Forced oil cooling |
| 1.23 | Operating noise level | dB | ≤85 |
| 1.24 | Drawworks weight | t | 38 |
| 1.25 | Operating temperature range | °C | From –19 to +50 |
| 2Drawworks equipment | |||
| 2.1 | Drawworks housing | set | Included |
| 2.2 | Drum with pulley | set | Included |
| 2.3 | Planetary gearbox | set | Included |
| 2.4 | Main brake | set | Included |
| 2.5 | Auxiliary brake | set | Included |
| 2.6 | Pneumatic clutches | set | Included |
| 2.7 | Brake control system | set | Included |
| 2.8 | Lubrication system with pump | set | Included |
| 2.9 | Water or air cooling | – | Included |
| 2.10 | Protective guards and safety components | – | Included |
| 2.11 | Instrumentation set | – | Included |
| 2.12 | Equipment data sheet and certificate of conformity | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | 6×36WS-IWRC-1770 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 9A, ISO 2408 |
| 1.3 | Line diameter | mm | 32 |
| 1.4 | Line construction | – | 6 strands of 36 Warrington-Seale wires with an IWRC steel core |
| 1.5 | Number of wires in the line | pcs | 216 |
| 1.6 | Wire material | – | High-strength steel, 1770 MPa |
| 1.7 | Breaking load, minimum | kN | 565 |
| 1.8 | Minimum safety factor | – | 5:1 |
| 1.9 | External coating | – | Anti-corrosion, type A lubricating coating |
| 1.10 | Lubricant type | – | Grease, water-resistant and frost-resistant |
| 1.11 | Line flexibility | – | High (“Flexible” category) |
| 1.12 | Lay direction | – | Right-hand, regular (Z-Lay) |
| 1.13 | Core diameter (IWRC) | mm | 13 |
| 1.14 | Weight per metre of line | kg | 4,34 |
| 1.15 | Working line length | m | 4000 |
| 1.16 | Operating temperature range | °C | From –40 to +50 |
| 1.17 | Certification | – | API Monogram, ISO 9001 |
| 1.18 | Corrosion resistance class | – | C2 (enhanced) |
| 1.19 | Warranty period | months | 12 |
| 1.20 | Recommended storage period | months | 24 |
| 2Drilling-line equipment | |||
| 2.1 | Line coil | set | Included (1 coil × 4000 m) |
| 2.2 | DIN 741 wire-rope clips | pcs | 30 |
| 2.3 | Reinforced steel thimbles | pcs | 6 |
| 2.4 | Line-end fittings (hook, shackle) | set | Included |
| 2.5 | Marking set and quality certificate | – | Included |
| 2.6 | Maintenance lubricant set | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | Wire-rope slings with reinforced thimbles |
| 1.2 | Applicable standard and technical specifications | – | API Spec 8C, ISO 7531 |
| 1.3 | Wire-rope material | – | High-strength steel, 1770 MPa |
| 1.4 | Line construction | – | 6×36WS-IWRC |
| 1.5 | Line diameter | mm | 32 |
| 1.6 | Sling length | m | 12 |
| 1.7 | Rated load | t | 225 |
| 1.8 | Breaking load | kN | 565 |
| 1.9 | Thimble type | – | Reinforced, forged steel |
| 1.10 | Swaging method | – | Aluminium ferrule swaging |
| 1.11 | Coating type | – | Anti-corrosion, lubricating |
| 1.12 | Suspension type | – | For suspending the travelling block from the crown block |
| 1.13 | Weight of one sling | kg | 45 |
| 1.14 | Number of slings per set | pcs | 2 |
| 1.15 | Operating temperature range | °C | From –40 to +50 |
| 1.16 | Certification | – | API Monogram, ISO 9001 |
| 1.17 | Safety class | – | Conforms to group G4 |
| 1.18 | Safety factor | – | 5:1 |
| 1.19 | Warranty period | months | 12 |
| 1.20 | Recommended storage period | months | 24 |
| 2Sling equipment | |||
| 2.1 | Wire-rope sling with thimbles | set | Included (2 pcs) |
| 2.2 | Reinforced thimbles | pcs | 4 |
| 2.3 | Swaging ferrules | pcs | 2 |
| 2.4 | Certificates and equipment data sheets | – | Included |
| 2.5 | Identification tags | – | Included |
| 2.6 | Storage and transport set | – | Included (wooden container) |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | RTSL-500 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 7K |
| 1.3 | Maximum static load moment | kN·m | 50 |
| 1.4 | Maximum torque | kN·m | 48 |
| 1.5 | Maximum table speed | rpm | 300 |
| 1.6 | Table internal diameter | mm | 500 |
| 1.7 | Rotary-pin seating diameter | mm | 445 |
| 1.8 | Drive type | – | Mechanical, via cardan drive |
| 1.9 | Gearbox type | – | Planetary |
| 1.10 | Lubrication system | – | Forced, with filtration |
| 1.11 | Brake type | – | Mechanical disc brake |
| 1.12 | Cooling system | – | Oil, natural circulation |
| 1.13 | Housing material | – | Cast 42CrMo steel |
| 1.14 | Rotary-table material | – | 35CrMo steel, heat-treated |
| 1.15 | Bearing assembly | – | Radial-thrust roller bearings |
| 1.16 | Rotary axis inclination angle | degrees | 0 |
| 1.17 | Rotary-table weight | t | 9,5 |
| 1.18 | Operating temperature range | °C | From –19 to +50 |
| 1.19 | Electric-drive explosion protection class | – | Ex d IIB T4 |
| 1.20 | Rotary-table housing earthing | – | Included |
| 2Rotary-table equipment | |||
| 2.1 | Rotary-table housing | set | Included |
| 2.2 | Complete rotary table | set | Included |
| 2.3 | Planetary gearbox | set | Included |
| 2.4 | Cardan drive | set | Included |
| 2.5 | Lubrication system with filter | set | Included |
| 2.6 | Braking system | set | Included |
| 2.7 | Instrumentation set | – | Included |
| 2.8 | Protective guards | – | Included |
| 2.9 | Equipment data sheet and API certificate of conformity | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | TDS-500 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 8C, API Spec 7K |
| 1.3 | Rated lifting capacity | t | 225 |
| 1.4 | Rated torque | kN·m | 50 |
| 1.5 | Maximum torque | kN·m | 65 |
| 1.6 | Maximum rotational speed | rpm | 250 |
| 1.7 | Through-bore diameter | mm | 500 |
| 1.8 | Drive type | – | AC electric drive |
| 1.9 | Electric motor power | kW | 500 |
| 1.10 | Supply voltage | V | 600 |
| 1.11 | Supply frequency | Hz | 50 |
| 1.12 | Control system type | – | PLC with touchscreen |
| 1.13 | Transmission type | – | Planetary, two-speed |
| 1.14 | Brake type | – | Automatic electromagnetic brake |
| 1.15 | Suspension type | – | Via carriage on mast guide rails |
| 1.16 | Maximum hydraulic system pressure | MPa | 20 |
| 1.17 | Lubrication system | – | Centralised, forced |
| 1.18 | Cooling type | – | Forced air cooling |
| 1.19 | Parameter monitoring system | – | Full telemetry (torque, speed, load) |
| 1.20 | Electric motor explosion protection class | – | Ex d IIB T4 |
| 1.21 | Top-drive weight | t | 9,8 |
| 1.22 | Operating temperature range | °C | From –20 to +50 |
| 2Top-drive equipment | |||
| 2.1 | AC electric motor | set | Included |
| 2.2 | Two-speed planetary gearbox | set | Included |
| 2.3 | Rotating spindle with wash head | set | Included |
| 2.4 | PLC control system | set | Included |
| 2.5 | Braking system | set | Included |
| 2.6 | Hydraulic power unit | set | Included |
| 2.7 | Cable drum and power cables | set | Included |
| 2.8 | Suspension carriage and guide rails | set | Included |
| 2.9 | Air cooling system | set | Included |
| 2.10 | Instrumentation set | – | Included |
| 2.11 | Equipment data sheet, manual, API certificates | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | F-1300 |
| 1.2 | Applicable standard and technical specifications | – | API Spec 7K |
| 1.3 | Rated power | hp | 1000 |
| 1.4 | Number of cylinders | pcs | 3 |
| 1.5 | Piston diameter | mm | 180–200 |
| 1.6 | Plunger stroke | mm | 305 |
| 1.7 | Maximum operating pressure | MPa | 34,5 |
| 1.8 | Maximum flow rate (180 mm diameter) | L/min | 1250 |
| 1.9 | Maximum flow rate (200 mm diameter) | L/min | 1450 |
| 1.10 | Crankshaft speed | rpm | 120 |
| 1.11 | Volumetric efficiency | % | ≥95 |
| 1.12 | Mechanical efficiency | % | ≥90 |
| 1.13 | Lubrication system type | – | Forced, with pump |
| 1.14 | Cooling type | – | Water or air |
| 1.15 | Drive type | – | Mechanical, via cardan drive |
| 1.16 | Rotation direction | – | Clockwise |
| 1.17 | Suction valve type | – | Ball valve |
| 1.18 | Discharge valve type | – | Ball or poppet valve |
| 1.19 | Valve and seat material | – | Nitrided 20Kh13 steel |
| 1.20 | Piston material | – | Polyurethane or NBR rubber |
| 1.21 | Cylinder liner material | – | High-hardness cast iron or chrome-plated steel |
| 1.22 | Suction pipe diameter | mm | 200 |
| 1.23 | Discharge pipe diameter | mm | 100 |
| 1.24 | Pump weight | t | 12,5 |
| 1.25 | Operating temperature range | °C | From –20 to +50 |
| 2Mud-pump equipment | |||
| 2.1 | Pump housing | set | Included |
| 2.2 | Three piston sections | set | Included |
| 2.3 | Complete valve box | set | Included |
| 2.4 | Working plungers | pcs | 3 |
| 2.5 | Cylinder liners | pcs | 3 |
| 2.6 | Discharge and suction valves | pcs | 6 |
| 2.7 | Seal set | set | Included |
| 2.8 | Lubrication system with pump | set | Included |
| 2.9 | Cooling system | set | Included |
| 2.10 | Pressure monitoring system | set | Included |
| 2.11 | Equipment data sheet, operating manual, API certificate | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | Stand Pipe Manifold |
| 1.2 | Applicable standard and technical specifications | – | API Spec 6A, API Spec 16C |
| 1.3 | Rated operating pressure | MPa | 35 |
| 1.4 | Maximum operating pressure | MPa | 40 |
| 1.5 | Working medium | – | Drilling mud, air, nitrogen |
| 1.6 | Bore diameter | mm | 76 (3”) |
| 1.7 | Number of outlets | pcs | 2–3 |
| 1.8 | Connection type | – | Flanged (API 6B / 6BX) |
| 1.9 | Leak-tightness class | – | PSL-2 |
| 1.10 | Housing material | – | 35CrMo or 4130 steel |
| 1.11 | Shut-off valve type | – | Manually operated wedge gate valves |
| 1.12 | Fitting type | – | API crosses, tees and nipples |
| 1.13 | Seal type | – | Metal-to-metal or BX rings |
| 1.14 | Pressure monitoring system | – | Glycerine-filled pressure gauges |
| 1.15 | Pressure gauge type | – | Vibration-resistant, scale up to 40 MPa |
| 1.16 | Emergency pressure relief system | – | Spring-loaded safety valve |
| 1.17 | Flange material | – | 35CrMo steel with anti-corrosion coating |
| 1.18 | Manifold mounting type | – | On the drilling rig frame |
| 1.19 | Manifold weight | t | 2,8 |
| 1.20 | Operating temperature range | °C | From –20 to +50 |
| 2Manifold equipment | |||
| 2.1 | Main high-pressure line (Ø3”) | set | Included |
| 2.2 | Wedge gate valves (API 6A, 35 MPa) | pcs | 2 |
| 2.3 | Pressure gauges (0–40 MPa, Ø100 mm) | pcs | 2 |
| 2.4 | Safety valve | pcs | 1 |
| 2.5 | Crosses and tees | set | Included |
| 2.6 | Adapters and nipples | set | Included |
| 2.7 | Mounting flanges | set | Included |
| 2.8 | BX sealing rings | set | Included |
| 2.9 | Supports and mounting frame | set | Included |
| 2.10 | Equipment data sheet and API certificates of conformity | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | Type | – | Mud Circulating System |
| 1.2 | Applicable standard and technical specifications | – | API Spec 7K, API RP 13C |
| 1.3 | Total system volume | m³ | 280 |
| 1.4 | Number of sections | pcs | 4 |
| 1.5 | Sand section capacity | m³ | 60 |
| 1.6 | Sludge section capacity | m³ | 60 |
| 1.7 | Clean mud capacity | m³ | 80 |
| 1.8 | Active section capacity | m³ | 80 |
| 1.9 | Tank material | – | Carbon steel with anti-corrosion coating |
| 1.10 | Tank wall thickness | mm | 6 |
| 1.11 | Agitation type | – | Mechanical and hydraulic |
| 1.12 | Number of agitators | pcs | 8 |
| 1.13 | Power of each agitator | kW | 7,5 |
| 1.14 | Number of sand pumps | pcs | 2 |
| 1.15 | Sand-pump power | kW | 45 |
| 1.16 | Shaker type | – | Dual linear-motion shale shaker |
| 1.17 | Number of shakers | pcs | 2 |
| 1.18 | Shaker screen size | mm | 1200×2500 |
| 1.19 | Shaker capacity | m³/h | 160 |
| 1.20 | Degasser type | – | Vacuum |
| 1.21 | Degasser capacity | m³/h | 240 |
| 1.22 | Desander type | – | Hydrocyclone, Ø300 mm |
| 1.23 | Desilter type | – | Hydrocyclone, Ø125 mm |
| 1.24 | Hydrocyclone material | – | Polyurethane or chrome-plated steel |
| 1.25 | Centrifuge type | – | Decanter, two-speed |
| 1.26 | Centrifuge capacity | m³/h | 40 |
| 1.27 | Centrifuge bowl material | – | Stainless steel |
| 1.28 | Cleaning system type | – | Sequential: shaker desander desilter centrifuge |
| 1.29 | Mud supply system | – | Via sand pumps |
| 1.30 | Lighting system | – | Explosion-proof, IP65 |
| 1.31 | Heating system | – | Electric, modular |
| 1.32 | Operating temperature range | °C | From –20 to +50 |
| 1.33 | Assembled system weight | t | 42 |
| 2Mud-system equipment | |||
| 2.1 | Sectional tanks (4 pcs) | set | Included |
| 2.2 | Mechanical agitators | pcs | 8 |
| 2.3 | Sand pumps | pcs | 2 |
| 2.4 | Vibrating shale shakers | pcs | 2 |
| 2.5 | Vacuum degasser | pcs | 1 |
| 2.6 | Desander | pcs | 1 |
| 2.7 | Desilter | pcs | 1 |
| 2.8 | Mud centrifuge | pcs | 1 |
| 2.9 | Piping and fittings | set | Included |
| 2.10 | Control panel | set | Included |
| 2.11 | Lighting and heating | set | Included |
| 2.12 | Equipment data sheet and API / ISO certificates | – | Included |
Scroll sideways to view all columns.
| No. | Equipment | Unit | Technical specification |
|---|---|---|---|
| 1Main technical specifications | |||
| 1.1 | System type | – | Drilling rig auxiliary equipment package |
| 1.2 | Applicable standard and technical specifications | – | API Spec 7K, IEC Ex, ISO 9001 |
| 1.3 | Pneumatic system | – | Central system with receiver and compressor |
| 1.4 | Compressor type | – | Electric screw compressor |
| 1.5 | Compressor capacity | m³/min | 6 |
| 1.6 | Operating pressure | MPa | 0,8 |
| 1.7 | Receiver capacity | L | 1000 |
| 1.8 | Water supply system | – | With pump and 10 m³ tank |
| 1.9 | Water pump type | – | Electric centrifugal pump |
| 1.10 | Pump capacity | m³/h | 60 |
| 1.11 | Power supply system | – | From diesel generators |
| 1.12 | Main generator power | kW | 600 |
| 1.13 | Standby generator power | kW | 300 |
| 1.14 | Generator type | – | Perkins / Cummins, 400/230 V, 50 Hz |
| 1.15 | Generator fuel system | – | 10 m³ tank, two-stage filtration |
| 1.16 | Drilling-site lighting system | – | LED, explosion-proof IP65 |
| 1.17 | Electrical equipment earthing system | – | Copper-rod earth loop, resistance ≤4 ohms |
| 1.18 | Fire suppression system | – | Automatic water/foam system, 20 m³ reserve |
| 1.19 | Technical-room ventilation system | – | Forced, with filtration |
| 1.20 | Communication and alarm system | – | Intercom + emergency siren |
| 1.21 | Personal protective equipment | – | Helmets, harnesses, safety ropes |
| 1.22 | Crew accommodation unit | – | Container-type module, 12 persons |
| 1.23 | Climate control system | – | Air conditioning + heating |
| 1.24 | Operating temperature range | °C | From –25 to +50 |
| 1.25 | Average equipment service life | years | 15 |
| 2Auxiliary equipment package | |||
| 2.1 | Screw compressor with receiver | set | Included |
| 2.2 | Water supply pump | set | Included |
| 2.3 | Process-water tank | m³ | 10 |
| 2.4 | Main generator (600 kW) | pcs | 1 |
| 2.5 | Standby generator (300 kW) | pcs | 1 |
| 2.6 | Fuel tank with filtration system | set | Included |
| 2.7 | Lighting masts | pcs | 6 |
| 2.8 | Electrical distribution boards | pcs | 3 |
| 2.9 | Earthing loop | set | Included |
| 2.10 | Fire suppression system (tanks, pumps, piping) | set | Included |
| 2.11 | Ventilation units | set | Included |
| 2.12 | Intercom and emergency alarm | set | Included |
| 2.13 | Accommodation modules (living, kitchen, sanitary) | pcs | 3 |
| 2.14 | Spare-parts and tool set | – | Included |
| 2.15 | Equipment data sheet, manual, certificates | – | Included |
Let’s discuss the well programme, equipment configuration, operating loads and readiness requirements.
